Santa costume - hat and final - part 6

The last of the postings regarding making the Santa costume...
The Hat.. Unfortunately the shots I took during the sewing of the hats themselves did not come out (still figuring out why) I made two hats, one standard traditional hat which is basically a cone with a circumference of 650mm (26"), and a height of 600mm (24"). The second hat was a experimental model which will be described soon.
Each hat comprised of a velour outer, a red poly-cotton liner, and fur trim at the brim, and a fur trim pompom at the top.



Figure 1 - hats - Experimental, and Traditional

The liner was simply a truncated cone of similar dimensions to the traditional hat (circumference of 650mm, and a height cut down to 300mm. If worn by itself, it would resemble an oversized cap.

The outer was sewn along the edge (right sides facing, then turn inside out to conceal the stitching), and then the fur trim stitched to the outer so the stitching was facing inwards. The liner was then placed inside, pinned and stitched into place to cover the seams for the attachment of the fur trim at the brim.

The pompom at the apex of the cone was handstitched on.

The experimental hat (combination hat and scarf) was patterned on the traditional conical pattern, but then at the 350mm height, the cone was changed to it had a total height of 1800mm (72"). This meant that the hat resembled a long tube of approximately 100mm (4") diameter for most of it's length, with a flare at the end which took the diameter out to 200mm (8") for the last 350mm (14"). All other aspects of the hat (including the liner) were unaltered from the traditional pattern.



Figure 2 - Pompom making - material, and octagon

So the pompom would match the fur trim used elsewhere in the costume, I made the pompoms from the fur trim. A square of fabric was cut - approximately 150 x 150mm (6" x 6") and the corners folded inwards to form an octagon. A heavy thread was loosely stitched in at each corner, and then around again bisecting each  side making 16 points evenly spaced around the octagon. the thread was gently pulled up so the corners and sides pulled in, and the resulting hollow space was filled with assorted offcuts from the fur trim.



Figure 3 - Hollow created in pompom by pulling threads up

It was then pulled up tight and tied off resulting in a pompom which was about 65mm (2.5") in diameter. The heavy thread used to make the pompom and tie it off was left threaded to the hand needle during the previous steps, and then used to stitch the pompom to the hat's apex.



Figure 4- Pompom hand stitched to hat

Other accessories and costume tips.
 A couple of shots of the bag which attaches to the belt for holding keys, mobile phone, lollies (candy), etc. Simply a bag made of velour offcuts, and lined in poly cotton - simple belt loops on the back for attachment
Figure 5 shows the interior view of the pouch with a mobile phone, and some car keys in it for the test.


Figure 5- Pouch on belt - interior view



Figure 6 - Pouch on belt, exterior view

The wig/ beard I purchased off Ebay for the costume - 100% polyester, and quite good fit, and shape. It cost about $30 to buy including shipping.


Figure 7 - polyester wig and beard set.

And lastly, some white zinc sunscreen paint... I've played Santa before for various groups (Church, charities, clubs) and seen many others play the part.. I have fairly thick dark eyebrows which show through on most wigs. If I apply a smear of the white zinc to my eyebrows, they whiten out as if I've aged 50+ years, and they don't look out of place. - It beats my old trick of gluing threads from cotton balls to my eyebrows with PVA (White) glue.


Figure 8 - White zinc sunscreen paint (with other unused colours)



Unfortunately we were unable to find a local source of the white zinc paint without buying it in a triple pack with the other bright colours... they'll get fobbed off at some future date, since we're not big fans of running around with fluro blue, or pink faces.

Next project things to document... MOT spotwelder progress, reviewing books, and progress on other projects.

Santa costume - pants - part 4

let's wrap up the Santa Claus costume...

Pants - nothing spectacularly different there compared to the jacket - although there is one sewing tip worth pointing out...

Want inexpensive broad loom calico for projects? Look at Ikea. Ikea sells a quilt cover made of full width calico for about $8. That gives you 2 pieces of calico the full width and length of a QB quilt... in dollars per metre it's by far the cheapest calico I've ever found, even at the 900m width. Whenever I venture near an Ikea, a few of those quilt covers are always on the list, just for the cheap fabric. The SB cover is called "Bomull", I'd have to look up the QB sized one, but they're usually next to each other in the shop (says Des who hasn't been in Ikea for over 12 months...) IF it saves someone else money, it was worth putting here...



Figure 1. Cheap calico courtesy of Ikea

Basically the pants (I made two pairs) were made using the velour material and the patterns generated. I then lined the inside with the calico, and made a waistband of red polycotton.
The waistband has a drawstring channel in it, and suspender points.


Figure 2. Velour outer being pinned to calico liner

Originally the suspender points were simple tabs which the jaws of the suspenders could affix to, but during test wears I found the jaws would occasionally let go - to beat this issue, I added a small tab at the front with a button, and a larger tab at the back with a corresponding buttonhole. The suspender jaw grips the original tab, and then the buttonholed tab is fed through the loop on the jaw, and buttoned down so it cannot let go.



Figure 3 - original suspender tab



Figure 4 - buttonhole tab threaded through loop



Figure 5. Button tab visible



Figure 6. tab buttoned down for securing suspender




The fur trim added at the bottom has a band of seatbelt material added inside for weighting the cuff downwards, and accentuating the flare of the cuff so the boot is covered better. In the original test fit, the trim would ride up the boot and looked "dorky".. almost like Santa was wearing clamdigger pants. With the weighted trim, the pants naturally fall to the top of the ankle, and ride up only slightly when seated.
No trim is at the waist since it's under the jacket, and would make adjustment with the drawstring harder.


Still to cover... belt, and hats. I'll most likely wrap them both together just to get this documentation finished.

Santa costume - jacket - part 3

The jacket was made by cutting out the panels for the back, front panels, and sleeves as per the pattern developed in part 1.

The lay of the fabric was maintained based on the arrows in the patterns. Once sewn together, the lining was made from standard polycotton (as used in making applique quilts) using the same patterns, and then placing it inside the jacket with all seams facing inside the jacket.



Photo 1 - cutting fabric from pattern

The collar of the jacket needed to stand up so any clothes worn under the jacket will not show, I decided the jacket collar needed some stiffening. I designed a flat collar which resembles a mandarin collar from the back, but lays flat as it comes down the front panels.
The stiffener material I used is some seatbelt webbing I salvaged from some of the road-crash training cars.



Photo 2 -  Seatbelt and fur trim for collar and it's stiffening


I cut the seatbelt fabric to make the collar higher at the back, and tapering down as the collar crosses over at the front.

The liner was inserted inside the jacket outer, and pinned in place. This allowed for minor adjustments in fit, and the positioning of the internal pocket for the gloves which was sewn in place prior to joining the outer and inner together.


Photo 3 - Jacket outer and liner pinned together

I then stitched this into the fur trim and then stitched this into the layers between the jacket outer, and the liner. This was accomplished by turning the jacket (with it's liner) inside out, and stitching it all together, but leaving a turning area of about 300mm (12") unstitched at the back of the jacket.



Photo 4 - Fur trim pinned in place for sewing into jacket layers

Once the sewing was done, the jacket was turned "right side out" and the turning opening was closed by careful pinning and sewing. To reduce the appearance of the closed seam, I used a derivative of the bias tape method, where I sewed the fur trim to the outer, then reversed the lay so it sat properly and then over-sewed the seam with the liner held in place with pins, this concealed the stitching for the outer/trim seam, and allowed the seam for the liner/trim to be hidden in the seam of the first set of stitching - sorry no photos to simplify the description.


Photo 5 - the finished jacket showing the liner in place

The photo above (photo 5) is where I was trying to determine if a single width belt looked OK, compared to a double width belt.

The pants were made in a similar manner, but will be covered in another posting.

Santa Costume Finished - Part 2

Well the santa costume is done...
There will be more parts put up to show how the costume was made - stay tuned..

The costume comprises:
1 - Jacket with cross-over front panels, internal lining, internal pocket (for gloves), shaped collar, fur trim
2 - Pants - lined, with drawstring and suspender tabs, weighted shaped cuffs, fur trim (2 pair made)
3 - modesty panel under jacket
4 - belt with brass buckles, and attachable "pouch" for lollies, keys, phone, etc
5 - Hat - 2 made, one traditional, one "special"
6 - Boots
7 - Gloves
8 - Beard and wig


There will be pages made for the pants, jacket, and belt so I won't discuss them here.



Photo 1 - showing the traditional hat

The boots are an old pair of structural fire boots (tread worn away to nothing) which I polished up and they're now in the costume set.
The wig and beard were a set I bought on E-Bay
The modesty panel is basically a large calico bib which I put on under the jacket - it's sole purpose is to prevent my shirt showing through the beard between the front panels of the jacket. Last year I went straight to a "santa run" from work and my bright "safety orange" work shirt was showing through the beard - not a good look for Santa. I deliberately wore the same shirt in these photos just to make sure the costume completely covered my clothes without ruining the look.
The belt pouch is simply a lined bag with belt loops which can be threaded onto the belt so Santa has an external pocket for stowing lollies (candy), keys, mobile phone, etc



Photo 2 - the costume

The hats were fun.
I'll probably do a page on the hats, but some of the photos didn't work out so there will be some gaps in the documentation.
Basically one hat is the typical design - about 600mm (24") tall, whereas the other is 1800mm (72") tall. The second one was a fun piece I made to try a theory about a hat also being able to be a scarf. Both hats were made from the same crushed velour fabric that the jacket and pants were made from, and used the same fur trim for the brim, and the pom-pom. Both hats are lined as well.


Photo 3 - Santa with the longer hat

Since Bender kept me company outside whilst I was sewing, it's only fair he gets to try on the hat...


Photo 4 - Bender modelling the scarf-hat

Since I don't have a large model of the Santa  Robot, this will have to do...



Photo 5 - Santa and Bender - not menacing at all

I'll document the jacket, pants and belt over the next week (time permitting) and then get back to documenting (and working on) the MOT spotwelder, and a few other projects I'm trying to clear off the "to do" list.

Project costs (AUD):
about $80 for fabric
$30 for the beard and wig
approx 50 hours of sewing, metalwork, etc
maybe $10-20 for incidentals (power, threads, gas, etc)

The day after I completed this project my wife pointed out a costume for sale in one of the online clearance sites... the costume cost about $80 shipped, but it was a thin felt set - the type which only last 3-4 wearings before falling apart... I'd like to think this costume will last many many years so I hardly begrudge the costs in time or money.